Fabricate two L-shaped brackets of 1.25a€? x 3/16a€? metal. The brackets were 7.5 inches very long. I dona€™t has a bender, so I welded the angle on. I desired a decent curve, and twisting they in a vice woulda€™ve developed too-large a radius. In hindsight We probably could’ve accomplished this in just bending and more shape. These brackets will bolt to the side on the slider action sheet metal. The brackets include guaranteed with two 1a€? x 3/8a€? class 8 bolts, washers, van sheet-metal, securing crazy, anti-seize composite. I did sona€™t discover a necessity for support plates right here because the primary burden is actually absolute.
Fabricate two Z shaped brackets of 1.25a€? x 3/16a€? metal. These brackets comprise in addition 7.5 ins longer overall. These will bolt to your underside associated with floor on the van. To decrease the possibility of tearout or twisting a floor in an accident, I fabricated some backing plates 3 ins 
very long a€“ essentially really big washers. Those two brackets were protected with 1.5a€? x 7/16a€? class 8 bolts, supporting plates, van sheet-metal, a washer to amount out sheet-metal under the van, a locking addict, and anti-seize composite.
Prime and painting the components. We made use of rust oleum car muscles black primer, and plutonium black paint and clearcoat. The plutonium try fascinating products a€“ features a dried out time of less than six minutes, so that the total decorating processes took about an hour and fifteen minutes for one coating of primer, solitary layer of pigment, and single clearcoat.
Test suit the set-up. Test suitable revealed that the regulator would not remove the van framing and the whole container would have to be moved inboard about 1 inches. I also must lessen the top in the regulator assembly, therefore I replaced a-1 inches breast with a close breast. We eliminated the brackets, caught them in a vice and pounded bends into these to manage the move. This dinged upwards my personal paint, but oh well.
Apply the tank. Test the fit once more. This time around We have approximately half an inch of approval between the regulator as well as the structure. I will bring a wrench on any the fixtures I want to set later if necessary. There clearly was a cross frame representative straight coming in contact with the guts part of the container, which adds to the rigidity of this installation. As a whole they feels completely bomber.
Path the trunk area propane range through the backside for the tank, within the exhaust line, and terminate at long framework user simply on the other hand from the gas tank. Shield this part of the operate making use of the half-inch heatshield.
Course the feeder line the kitchen stove over the framing associate, crossing-over into the not in the van nearby the vehicle’s gas tank refill, moving right up into the interior wall surface with the van through very big 4 x 6 beginning in the B pillar
Route the feeder line for hot water heater straight over the van while watching rear wheel better, through a gap in the section of the wall, and up into the internal.
Protected all contours with half-inch stainless steel pipe clamps, 1/4a€? stainless screws and washers, and 1/4a€? plus peanuts. I personally use established holes from inside the framing in which feasible, and additionally a couple of 8 mm threaded holes.
Purge the container at local propane supplier.
Examination for leaks by starting the solenoid, after that closing and overseeing the pressure gauge.
You will find temperatures shielding regarding propane range in which it passes around exhaust system, but I’m still determining the need for shielding regarding the container itself. I went the van hot for an hour or so and mayn’t get the area of this tank go over ambient heat, but i am going to retest in the summertime and either atart exercising . heating shielding into the tank or expand the exhaust program heatshield.
Installment location
Preparing where the container should healthy. We finished up installing it more forth that I wanted because the point involving the back and front associated with tank harmonized ideal making use of step layer steel only at that place – however the onward edge of the tank is more exposed to the fatigue system. I don’t think it would be something.
Tank and its particular components
Beginning with the container a€“ POL valve, T, auxiliary container accessory fitting, backyard barbeque fitting, solenoid, pressure gauge, 2 level regulator, help group. The Manchester container degree determine is located at the low left, and refill port aided by the yellow cover is within the center.